• Elastic formulation with crack bridging (0.4 mm) properties.
• Wear-resistant, high impact strength.
• Good resistance to most industrial chemicals, including organic acids.
• Limited resistance to organic solvents.
• Darkens and yellows in UV light.
• Does not emit odors or flavors, is not flammable.

Application temperature: Provides safe and trouble-free curing between 10-30 ° C.
Is sensitive to high humidity during application and curing, RH <85%. Pot life: Pot life after mixing is approximately 30 min. Curing time: 24 hours for pedestrians. 2-3 days for lower loading . 5 days for complete curing and resistance. Mixing ratios: ERADUR PU 350, Comp A (16 kg) ERADUR PU 350, Comp B (3,5 kg) ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed. Keep the exact mixing ratio between component A and B. All materials should preferably have ambient temperature before use. Safety: Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product. Technical specification: Tensile strength ca 13 MPa Shore D ca 55 Density base: 1,5 gr/cm3 Viscosity about 2 Pa s Solid content 100% Gloss Blank Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® PU 350 εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

• Elastic formulation with crack bridging properties.
• Wear-resistant, high impact strength.
• Good resistance to most industrial chemicals, including organic acids.
• Limited resistance to organic solvents.
• Darkens and yellows in UV light.
• Does not emit odors or flavors, is not flammable.

Application temperature: Provides a safe and trouble-free curing between 10-30 ° C.
Is sensitive to high humidity during application and curing.
RF <85% (20 ° C). Pot life: Pot life after mixing is approximately 45 min. Curing time: 24 hours for pedestrians. 2-3 days for lower loading. 3 days for complete curing and resistance. Mixing ratios: 2 parts by weight of ERADUR PU FLEXSEAL, Comp A (17 kg) 1 part by weight of ERADUR PU FLEXSEAL, Comp B (3,2 kg) ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed. Keep the exact mixing ratio between component A and B. All materials should preferably have ambient temperature before use. Safety: Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product. Technical specification: Tensile strength ca 12 MPa Shore A/D 81/46 Break elongation,% 260% Density base: 1,3 gr/cm3 Viscosity about 1,5 Pa s Solid content 100% Gloss Blank Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® PU FLEXSEAL εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

• Exceptionally good abrasion resistant topcoat.
• Good light resistance and UV resistance.
• Water-borne with a discreet smell.
• Increases the cleaning-durability of polyurethane floors.
• Provides scratch resistance to epoxy coatings.
• Good resistance to heel marks.
• Good resistance to industrial chemicals, including organic acids.

Application temperature: Application temp (floor temp): 10-30 °C.
Curing time: 8-16 hours before the application of coating or painting.
16-24 hours for pedestrians and lower loading (depending on temperature). 2-6 days for complete curing and resistance.
Mixing ratios: 5 parts by weight of ERADUR TOPPLACK PU MATT, Comp A (4,0 kg)
1 part by weight of ERADUR TOPPLACK PU MATT, Comp B (0,8 kg)
Stir the base before adding a hardener. Mix base and hardener at least 3 minutes before adding any (depending on substrate) water, 5%, continue mixing about 1 minute after adding water. Add the same amount of water to avoid shine variation. The humidity must not exceed 75% RF during curing and the surface must be at least 3 ° C above the dew point. Potlife: about 40 minutes at 20 ° C.
Safety: Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product.
Technical specification: Density base: 1,05 gr/cm3
Harder: 1,15 gr/cm3
mixture: 1,07 gr/cm3
Solid content 45%
Gloss Matte
Consumption 100-120 g/m2
Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® TOPPLACK PU MATT εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

• Elastic formulation with crack bridging (0.4 mm) properties.
• Wear-resistant, high impact strength.
• Good resistance to most industrial chemicals, including organic acids.
• Limited resistance to organic solvents.
• Darkens and yellows in UV light.
• Does not emit odors or flavors, is not flammable.

Application temperature: Provides safe and trouble-free curing between 10-30 ° C.
Is sensitive to high humidity during application and curing, RH <85%. Pot life: Pot life after mixing is approximately 30 min. Curing time: 24 hours for pedestrians. 2-3 days for lower loading . 5 days for complete curing and resistance. Mixing ratios: ERADUR PARKINGBODY, Comp A (16 kg) ERADUR PARKINGBODY, Comp B (3,5 kg) ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed. Keep the exact mixing ratio between component A and B. All materials should preferably have ambient temperature before use. Safety: Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product. Technical specification: Tensile strength ca 13 MPa Shore D ca 55 Density base: 1,12 gr/cm3 Viscosity about 2 Pa s Solid content 100% Gloss Blank Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® PARKINGBODY εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

Product type

Two-component, solvent-free, colorless epoxy coating.

Application areas

Specially formulated primer for concrete surfaces.

Properties

Very good penetration and adhesion to concrete and other
mineral substrates. It provides secure interlayer adhesion.
Reinforces the concrete surface. Excellent for dust binding as it gives the concrete a dense, durable, and chemical-resistant surface.

Application temperature

Application temp (floor temp): 12-25 °C.

Pot life

Pot life after mixing is approximately 40 min.

Curing time

6-8 hours before the application of coating or painting.
12-16 hours for pedestrians and lower loading (depending on temperature). 7 days for complete curing and resistance.

Mixing ratios

2 parts by weight of ERADUR Primer N, Comp A (10 kg)
1 part by weight of ERADUR Primer N, Comp B (5 kg)
ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed.
The mixture should then be applied to the floor without delay, hardening occurs fast in the mixing vessel!
Keep the exact mixing ratio between component A and B.
All materials should preferably have ambient temperature before use.

Safety

Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product.

Technical specification

Density base: 1,11 gr/cm3

hardener

1,01 gr/cm3

mixture

1,08 gr/cm3
Viscosity ca 0,3 Pa s
Solid content 100%
Gloss Blank
Consumption ca 0,3 kg/m2
Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® PRIMER N εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

Product type

Two-component, solvent-free and anti-static pigmented epoxy plastic.

Color

The ESD coating can be performed in most RAL and NCS colors. The carbon fibers are visible and breach the surface to ensure the ESD function in the product. See our color chart for suggestions on colors.

Application areas

– Designed for surfaces exposed to static electricity.
– Anti-static coating that counteracts sparks.
– Floor coatings for explosive-grade surfaces and potentially explosive atmospheres.
– The anti-static properties are adapted to different industries, norms and standards.
– ESD security in sensitive areas such as computer halls, operating rooms and premises – where sensitive electronic equipment is installed, repaired, stored or used.

Properties

Provides a hard, dense, durable, and anti-static surface that can be adapted for any requirements for slip-resistance and chemical resistant. The adhesion to concrete and other mineral substrates is very good. The coating is made in 2-3 mm in layer thickness. The coating dissipates static electricity and counteracts sparks.
Withstands chemical stress… See separate chemical resistance table.
Neither bass nor hardeners are toxic. The product has a medium-low viscosity. The application is simple and does not require any special equipment other than that found in ordinary epoxy work. The desired properties are achieved reliably and smoothly. Emits no odours and is also non-flammable.

Application temperature

Provides a safe and trouble-free curing between 12-25 ° C (RF <80%)

Pot life

Pot life after mixing is about 35 min. (20 ° C)

Curing time

The curing time varies with the temperature.
At 20 ° C the coating can be stepped on after approx:
1-2 days for pedestrian traffic.
2-3 days for lighter load.
7-10 days for full curing and chemical resistance.

Mixing ratios

3,65 parts by weight ERADUR® ESD MASSIV comp A (15 kg)
1 part by weight ERADUR® ESD MASSIV comp B (4,1 kg)
ERADUR® ESD MASSIV is a two-component product, and any insufficient mixing will result in partially incomplete curing. Mix for several minutes before the application, make sure that all the material in the bottom and sides of the container is properly mixed.
Mixing ratios should be adhered to between component A and B.
All materials should be at room temperature before use.

Safety

Always use PPE material during mixing and application. Read the label and safety data sheet before using the product.

Το άρθρο ERADUR® ESD MASSIV εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

Product type

Waterborne anti-static epoxy primer intended for ESD coatings.

Application areas

Eradur ESD Coatings.

Properties

Electrically conductive primer with high conductivity.
It has good adhesion to most hard surfaces.

Application temperature

Application temp (floor temp): 15-25 °C. Use requires efficient air exchange and relative humidity: RF <80%.

Pot life

Pot life after mixing is approximately 30 min.

Curing time

8 hours for complete curing.

Mixing ratios

1 part by weight of ERADUR ESD Primer 1, Comp A (2,1 kg)
4 parts by weight of ERADUR ESD Primer 1, Comp B (8.5 kg)
Note that Eradur ESD Primer 1 should not be diluted but applied as
supplied with a rubber rake. It is necessary with
an even and accurate application of 0.12 kg per square meter.
ESD Primer 1 should be used as a basis for anti-static color sand coatings which is applied to stripped epoxy primer, ie Eradur Primer N or Eradur Plus Primer is strewn with quartz sand 0.7-1.2 mm, about 05 kg / m2.
The supply is increased on stripped primer to about 0.14 kg / m2.
Copper tape and ground connection must be made on underlying layers.
ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed.
Keep the exact mixing ratio between component A and B.
All materials should preferably have ambient temperature before use.

Safety

Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product.

Το άρθρο ERADUR® ESD PRIMER 1 εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

Product type

Two-component, solvent-free, pigmented epoxy coating. Adhesive Component in Eradur Massiv SL and Eradur Struktur when performed as monochrome.

Application areas

– Thick film painting: 0.5 – 1 mm
– Self-leveling coatings: 2 – 5 mm.
– Pigmented sand coatings: 3 – 15 mm.

Properties

It provides a hard, durable and non-porous surface that can be adapted to the requirements of slip-resistance. The adhesion to concrete and other mineral substrates is good. The coating provides a distribution of point loads at thicknesses above 4 mm.
Good chemical-resistance. Withstands gasoline, oils grease, salts, water, etc. Limited resistance to strong acids and strong solvents. The resistance to
alkali and lye is good. Eradur Massiv SL is odorless and not flammable.

Application temperature

Application temp (floor temp): 12-25 °C. (RF < 80% Air, RF < 93% Concrete). Can also be applied at other temperatures, but requires a special hardener.

Pot life

Pot life after mixing is approximately 40 min.

Curing time

12-16 hours for pedestrians and lower loading.
5-7 days for complete curing and resistance.
Several curing agents with different curing properties are available, e.g.
– Massiv SL, B provides the best possible flow properties with slow curing.
– Massiv SL LE, B provides a low emission coating.
– Massiv SL U, B provides a curing time of about 4-6 hours

Mixing ratios

Base: 3,41 parts by weight of ERADUR Massiv SL, Comp A (11,6 kg)

Hardener

1 part by weight of ERADUR Massiv SL, Comp B (3,4 kg)

Filler

4,41 parts by weight of ERADUR Massiv SL, Comp C (15 kg)
(Comp C only used for self-leveling coatings).
ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed.
Keep the exact mixing ratio between component A and B.
All materials should preferably have ambient temperature before use.

Safety

Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product.

Technical specification

Compressive strength ca 87 MPa
Tensile strength ca 41 MPa, i.e. fracture in concrete
Flexural strength ca 27 MPa
Shore D ca 82
Solid content 100%
Gloss Blank
Consumption ca 0,3 kg/m2
Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® MASSIV SL εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

Product type

Two-component, solvent-free anti-static epoxy topcoat.

Application areas

ESD security in sensitive areas such as computer halls, operating rooms and premises – where sensitive electronic equipment is installed, repaired, stored or used.
Topcoat and sealing used for colored sand floors.
Designed for surfaces exposed to static electricity.
Properties:

• Good mechanical properties.
• Anti-static topcoat that counteracts sparks.
• The anti-static properties are adapted to different industries, norms and standards
• Low yellowing and good light fastness.
• Very good resistance to inorganic acids, alkali, gasoline, and oils.

A high-quality clear coating formulated for use as a topcoat for coatings with high demands on low yellowing, high light fastness in combination with abrasion resistance and durability. It can also be used for colored sand coatings and gives very good mechanical properties and high impact resistance to the coating. The product emits no odors or flavors and is not flammable.

Application temperature

Application temp (floor temp): 10-30 °C.

Pot life

Pot life after mixing is approximately 50-60 min.

Curing time

24 hours for pedestrians and lower loading. 5-7 days for complete curing and resistance.

Mixing ratios

2 parts by weight of ERADUR TOPPLACK, Comp A (10 kg)
1 part by weight of ERADUR TOPPLACK, Comp B (5 kg)
ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed.
Keep the exact mixing ratio between component A and B.
All materials should preferably have ambient temperature before use.

Safety

Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product.

Technical specification

Tensile strength ca 45 N/mm2 i.e. fracture in concrete
Flexural strength ca 65 N/mm2
E-module ca 2400 N/mm2
Compressive strength ca 70 N/mm2
Impact resistance ca 50 mJ/mm2

Density base

1,12 gr/cm3

hardener

1,00 gr/cm3
Glass transition temperature ca 42 °C
Viscosity about 0,4 Pa s
Solid content 100%
Gloss Blank
Shelf life 6 month

Το άρθρο ERADUR® ESD TOPPLACK εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.

• Good mechanical properties.
• Good resistance to industrial chemicals.
• Good resistance to strong inorganic and organic acids.
• Heat resistant, TG> 110 ° C, withstands hot water and steam cleaning. Darkens and yellows in UV light.
• Does not emit odors or flavors, is not flammable.

Application temperature: Provides a safe and trouble-free curing between 10-30 ° C.
Is sensitive to high humidity during application and curing.
RF <85% (20 ° C). Pot life: Pot life after mixing is approximately 30 min. Curing time: 8-16 hours for pedestrians. 2-3 days for lower loading. 3 days for complete curing and resistance. Mixing ratios: ERADUR PU 750, Comp A (15 kg) ERADUR PU 750, Comp B (4,5 kg) ERADUR is a two-component product, and an insufficient mixing will result in partially incomplete curing. Mix for several minutes with a machine just before the application, make sure that all material in the bottom and rim of the container is properly mixed. Keep the exact mixing ratio between component A and B. All materials should preferably have ambient temperature before use. Safety: Wear safety goggles and protective clothing during mixing and application. Read the label and safety data sheet before using the product. Technical specification: Tensile strength ca 20 MPa Bending strength ca 30 MPa Compressive strength ca 54 MPa Density base: 1,4 gr/cm3 Viscosity about 1,2 Pa s Solid content 100% Gloss Blank Shelf life 6 months in an unbroken container (>15 °C).

Το άρθρο ERADUR® PU 750 εμφανίστηκε πρώτα στο Golvet - Εμπορία Υλικών Δαπέδων.